The RC Geek Blog

By: Chris Wolfe

Finishing Fiberglass – Let’s finish that dorsal!

Last time we finished up construction of our rudder/dorsal assemblies and built our offset rudder hinge.  So, now it’s time to clean these assemblies all up and make them as ready as they can be to be installed onto the fuselage.  The installation of the dorsal onto the fuselage will occur once all of the construction of the fuse is finished however.  The primary reason for this is so that all work on the fuselage can be done without the dorsal being in the way as the fuselage is rotated around while it’s worked on.

Primer – Sand…repeat, repeat, repeat…
With the dorsal and rudders being glassed (see Part 5 for that discussion), the first item of business is to start the primering process.  The objective for finishing fiberglass here is two-fold:

  1. To fill in the weave of the cloth and create a smooth surface finish
  2. To find any imperfections that need additional attention and filling

To fill in the cloth weave, the process I use is to simply apply a coat of primer, sand it down, and repeat until the surface is smooth.  Another method is to apply a second coat of finishing resin which works well also, but requires quite a bit of sanding and can add weight.  Regardless, more than 1 coat of primer is usually required to get a fully smooth surface anyhow so we can cut to the chase with the single resin layer and just use the primer for filling.

buld an rc jet - skyray primer The primer I use is EVERCOAT which is available through my folks at Jet Hangar.  Applying the first coat, I apply it down fairly wet and then let it dry and repeat on the other side.  Once dry, using a sanding block with 180 grit sand paper applied to it, I sand the primer away back down to the cloth layer.  Though you can hand sand it using sanding  paper only, the reason for using a sanding block is that this evens out the surface as the layers of primer are added.  While sanding, there are areas of primer that won’t sand away completely which is to be expected, that’s the primer doing it’s job of filling!  Once sanded down, more primer is applied and this process repeats until the surface is smooth.  Typically it will take about 2-4 coats.

Once sufficiently smooth, any areas that couldn’t be smoothed out with the primer are individually filled using a glazing putty.  I prefer 3M Acryl-White Putty as it fills nicely, sands well and gives a smooth surface.  However, this is for small surface imperfections.  Any deep imperfections require Icing filler to fill as the glazing putty doesn’t have sufficient body to hold shape for deep imperfections.



Details, details…
To finish off the dorsal/rudder assembly, there are a few details necessary.  First off, the Skyray has a very definitive fuel dump mast at the top of the rudder with 4 slots in it where the fuel would exhaust through.  To make this part, I designed the two ends (radial slotted base and tip with open slots) in Rhino and had them 3D printed out of SLA.  Those two ends were then glued into a 1/4″ diameter aluminum tube of the appropriate length.  The result is a very convincing and robust part.  The whole part could have been 3D printed and I looked at doing that.  However, I was looking for a light weight solution and wanted to avoid printing a solid part for that reason (I did have a single piece hollow part printed of the entire mast, but it warped). The mast will be final installed onto the dorsal just prior to gluing the dorsal on.

The other details necessary (in my mind) are the scale actuator linkages that are within the slots for the hinges on the full size airplane.  These were also designed in Rhino and 3D printed.  They were printed as a single part, however the CAD model was toleranced sufficiently such that after being printed the rod parts were in fact moveable. This way, they move as the rudder moves and it didn’t require anything additional to do so.  This is the beauty of a very high resolution 3D print!  It saved me lots of time and heartache trying to hand craft something.  You can see the results compared to their full scale counterparts below.

For comparison, here are some pictures of the full size counter part.  This is the look we are trying to achieve…without the bird pooh of course!

So, at this point, the dorsal is as finished as it will be before installing it onto the fuselage.  We still need to run the lighting for the solid white navigation light in the dorsal, but that can come at anytime prior to installing the dorsal onto the fuselage.  Also, we still need to final install the rudders too.  Again, that will occur just prior to dorsal installation on the fuse.  From here we will set aside the dorsal a while as we start to work in on the fuselage (fuse has to be done to setup the wing installation).  So, enjoy your rest my friend, we will see you again soon…

 

The post How to Build an RC Jet – Part 6 appeared first on The RC Geek.

The RC Geek Blog is your place to learn about all aspects of the RC hobby. Learn to build, design, drive or fly that RC project you’ve always wanted to build, but have been intimidated to try. This blog is here to help you on your journey and provide tips and tricks as you go! My hope is to inspire builders both experienced and new! So, welcome, please look around, it’s an exciting beginning!  I’m currently documenting my latest competition scale RC jet build, a Mark Frankel F4D Skyray, along with some other fun tips and videos. If you can’t find what you’re looking for on this front page, click on any of the categories to the right and it will show just posts related to those categories. Please feel free to add comments and/or contact me directly if you have questions, I’m here to help! And don’t forget to check out my YouTube Channel, I post new videos every week!

Subscribe To Our Blog Now

By Chris Wolfe 19 Sep, 2023
The B-58 Hustler Saga - From Triumph to Tragedy
By Chris Wolfe 13 Mar, 2023
Preparing for Battle: The ULTIMATE Guide to Scale Documentation Maybe you've heard about RC Scale Aircraft competitions, but the thought it sounded intimidating, or the process of it all seemed daunting and discouraging. Well, fear not! I am here to encourage you and dispel any myths you may have heard if any. Scale competition is a fun and challenging segment of the hobby that will undoubtedly make you a better pilot! So, in light of this, I've started a new "Preparing for Battle" live series and in my first episode, "Preparing for Battle: The ULTIMATE Guide to Scale Documentation," we talk about the AMA Scale Nats with special guest Joe Vermilion from Balsa USA and peel back the layers of scale competition and provide information on what it's all about! As an experienced RC Scale Aircraft competitor and two time US Scale Masters National Champion, my hope is to share whatever knowledge and practical advice I can for newcomers and seasoned competitors alike.
By Chris Wolfe 14 Feb, 2023
Are You Ready to Take Your RC Flying to the Next Level?? Then you’re in luck, because we’re giving away an FMS 1400mm F4U Corsair and an FMS 1100mm PC-21 ! But first, let's address the elephant in the room...it's been quite a while since my last blog post. With the move to TN and everything going on trying to get The RC Geek up and running full time, it's been difficult to sit down and set aside time to write. My goal is to change that going forward, so here's hoping! (check the vid below for even more details about everything mentioned here!)
By Chris Wolfe 25 Jan, 2022
Flight of the Flir Cat…The Sequel!! I tell you what, it has been quite the journey getting here! As a project, this Freewing F-14 Tomcat refinish took much longer than I had originally planned based on all of the other distractions that have come through the shop, but I'm so happy with how this model turned out in the end. It did take a few flights to get tuned and I have made a few small modifications in the process since our last installment, but otherwise I'm happy to report that the Tomcat is flying quite well. The F-14 Tomcat has such a great look and presence in the air, you just can't beat it!
By Chris 10 Jan, 2022
10 channels of power…and 1 receiver to rule them all! I personally love having the option for more channels, especially when building my own scale aircraft. While not always necessary, having channel options available is almost always helpful and it opens up opportunities to add scale functions and/or customize the controls more to your liking. And that's not to mention having individual servo setup across the same functions. So, I was excited to finally see the AR103060T and AR10100T 10 channel receivers released from Spektrum. It opens of channel options in a lighter weight package while also supports all of their new technology. Having been flying the NX10 for some time it is nice to finally be able to utilize all of those 10 radio channels.
By Chris 10 Jan, 2022
Good times and Warbird Flying are back! Needless to say, the last year and a half plus has been hard on all of us. With so many of our normal routines and activities disrupted, it has only brought that many more challenges it seems. This hobby is not just about the airplanes and flying, it is about the friends and comradery that can be enjoyed together with others as well. So, when the Scale Squadron's Warbirds & Classics came up again this year after being cancelled in 2020, I was beyond excited to go; it had been almost 2 years since the last event I went to!
By Chris 24 Nov, 2021
Refinish a Foam Jet Ep 4 – Freewing F-14 Tomcat Low-Viz Navy Weathering How low can you go?…a little low-viz Tomcat weathering. Finishing up the refinish work on the Freewing F-14 Tomcat, it’s time to apply some characteristic low-viz Navy weathering. The Flir Cat paint scheme is from the mid 90’s at a time when the Tomcats in service were painted primarily in Dark Ghost Grey (FS36320) with variations thereof. They were high maintenance workhorses at this time and the aircraft got extremely dirty during operation. This opens up lots of opportunities to apply different weathering techniques on the airplane to simulate those years of service on the carrier.
By Chris 24 Nov, 2021
Refinish a Foam Jet Ep 3 – Freewing F-14 Tomcat Paint, Markings, & Panel Lines
By Chris 27 Sep, 2021
Refinish A Foam Jet Ep 2 - Freewing F-14 Tomcat Cockpit 3D Printing, Painting and Moving Pilots
By Chris 27 Sep, 2021
Fill…sand…poly…sand…primer…sand…aaaannnnddd repeat… You've probably figured out by now, I have many favorite aircraft. ;) However, if I was to put together my top 5 favorite aircraft of all time, the F-14 Tomcat would probably be at or near the top of that list. The airplane was one of brute force, but packaged in an elegant and distinct looking airframe that truly personified its name, Tomcat. And that's not to mention, it was an extremely capable fighter that filled many roles through the years that operated from the early/mid 70's into the mid 2000s.
More Posts
Share by: