The RC Geek Blog

By: Chris Wolfe

Fiberglassing and Hinges…now we’re getting somewhere!

buld an rc jet - skyray 40 With the dorsal and rudder shaped, the next step is fiberglassing and hinging each of the parts.  I didn’t take many pictures during the glassing process (performed this before starting this blog), but I will talk through it a little bit.  When I get to fiberglassing the wings, I plan to make a complete tutorial video.  The pic to the left is ultimately what we are striving for…

Some Notes on Fiberglassing

Now, I typically don’t hinge control surfaces until  after glassing.  I’ve done it both ways (hinging before and after glassing) and have found hinging after glassing is definitely my preference.  The reason for this is that when I make the slots in the control surfaces to receive the hinges, I can get much cleaner and crisper corners since the glass hardens the wood.  Otherwise, the balsa can crush in around the slot and it doesn’t come out as cleanly.  In terms of glassing, I use 3/4 oz fiberglass cloth and Pacer Z-Poxy Finishing Resin  finishing epoxy resin to apply the glass.  The fiberglass is cut out around the surface allowing significant overlap and laid flat onto the surface dry (important!).  From there, I mix up the Z-Poxy Resin  as directed (50/50 mix on a scale) in a paper cup.  I drizzle it onto the dry fibreglass in the center of the surface and then wet out the glass (while on the surface) using an old credit card or something similar as a squeegee.  I wet out the glass from the center out towards the edges until the entire surface is covered.  There should be no pooling of resin once done, so make sure to squeegee any excess as this is just extra weight otherwise.  For the leading edge, it’s important to get some overlap around so that you get full coverage when glassing the other side (at least 3/4 coverage around the LE).  This also adds some additional hardness since if done right, you will get a double layer of fiberglass over the LE.  For the trailing edge, the glass should be wetted to about 1/4-1/2″ past the trailing edge of the actual surface.  This is again for full coverage, but also so that when the opposite side is glassed, it creates a stiff trailing edge that once cured can be sanded to a nice sharp point at about 1/32-1/16″ past the wood trailing edge.

Dorsal glassed and curing

Rudder glassed and curing

 

Offset Rudder Hinge

buld an rc jet - skyray 30 With the surfaces fiberglassed, it is then a matter of hinging the rudder.  The Skyray has a pretty distinct rudder setup having large hinge cutouts while also being split into an upper yaw damper and lower rudder. The cutout outlines were first transferred to the rudder along with the rudder/yaw damper split line using the plans as well as my reference material ( see this post for a discussion of that ).  The cutouts were made first using a razor saw as well as an Xacto knife with a metal straight edge.  The key is to ensure everything is as desired before making any cuts at all and then in the process of cutting taking time to ensure straight cuts.  Any areas where I overcut or weren’t quite square, I used USC Icing  (two part filler like bondo) to fill in.  In the case for the large cutout, I didn’t quite get the cuts square, so I took a piece of 1/64″ ply, applied a piece of packing tape to it and cut it on the back side (not penetrating through the tape) so that it could be folded into the shape of the cutout.  I then tack glued it into the opening and filled with the Icing any open spaces to get clean corners and a square opening.  The beauty is that the Icing will not stick to the packing tape once cured completely.

All surfaces cut, ready for hinging

 

Once happy with the hinge cutouts, the rudder was split into a top and bottom in much the same way using an Xacto with a straight edge and a razor saw to cut through the 1/64″ ply trailing edge stiffener.  The end caps were made simply by lightly wetting a paper towel with some lacquer thinner, touching the foam to lightly melt a little of it on the ends of the rudders, and then using a balsa wood filler to fill in the space (they can also be capped with 1/64″ plywood as well but requires removal of 1/64″ material on each end first).

buld an rc jet - skyray 39 The Skyray has an offset hinge on the rudder, so before starting on hinging the surface, it was necessary to plot out where the hinge location should be.  The plans and documentation resources were referred to do this and then the location was plotted on the rudder.  The dorsal hinge supports were plotted also and made out of plywood of the appropriate thicknesses to achieve a scale look for each hinge bracket.  A 3/32″ aluminum tube was embedded through the hinge location on each of the supports. This in turn required embedding 3/32″ alum tube in the rudder parts as well.  This had to be done by slotting the LE of the rudder the appropriate width, embedding the aluminum tube into the rudder along the hinge line and then replacing the removed material from the LE and resanding it to shape.  The bare wood was then sealed simply by brushing some mixed Z-Poxy over the exposed wood and then lightly sanding it once cured.  To mount the hinge brackets, it required cutting slots in the rudder spar at the appropriate locations to receive the plywood hinge supports.  With all of this done, the rudder hinge is then created by placing a 1/16″ wire through the tubing in the rudder and hinge brackets.  With everything aligned properly, you get an extremely smooth hinge that actuates representatively to the full size aircraft.  The wire will be held in place with a cap over the middle hinge support (upper yaw damper will be fixed) once everything is ready for final install.

Installing the Torque Rod

The last item of business is installing the rudder torque rod which was done by removing the foam in the area of the torque rod and installing a balsa block.  From there, a slot was cut in the leading edge of the rudder to allow for the torque rod to be inset into the rudder.  It is aligned so that the center of the torque rod lines up as an extension of the rudder hinge line (very important).  This minimizes any lateral movement once everything installed which alleviates any biases that could be imparted onto the rudder servo and linkage assembly.

Next time we’ll talk about detailing and finishing our rudder and dorsal assembly.  That’s where the hard work and prep really starts to pop!

The post How to Build an RC Jet – Part 5 appeared first on The RC Geek.

The RC Geek Blog is your place to learn about all aspects of the RC hobby. Learn to build, design, drive or fly that RC project you’ve always wanted to build, but have been intimidated to try. This blog is here to help you on your journey and provide tips and tricks as you go! My hope is to inspire builders both experienced and new! So, welcome, please look around, it’s an exciting beginning!  I’m currently documenting my latest competition scale RC jet build, a Mark Frankel F4D Skyray, along with some other fun tips and videos. If you can’t find what you’re looking for on this front page, click on any of the categories to the right and it will show just posts related to those categories. Please feel free to add comments and/or contact me directly if you have questions, I’m here to help! And don’t forget to check out my YouTube Channel, I post new videos every week!

Subscribe To Our Blog Now

By Chris Wolfe 19 Sep, 2023
The B-58 Hustler Saga - From Triumph to Tragedy
By Chris Wolfe 13 Mar, 2023
Preparing for Battle: The ULTIMATE Guide to Scale Documentation Maybe you've heard about RC Scale Aircraft competitions, but the thought it sounded intimidating, or the process of it all seemed daunting and discouraging. Well, fear not! I am here to encourage you and dispel any myths you may have heard if any. Scale competition is a fun and challenging segment of the hobby that will undoubtedly make you a better pilot! So, in light of this, I've started a new "Preparing for Battle" live series and in my first episode, "Preparing for Battle: The ULTIMATE Guide to Scale Documentation," we talk about the AMA Scale Nats with special guest Joe Vermilion from Balsa USA and peel back the layers of scale competition and provide information on what it's all about! As an experienced RC Scale Aircraft competitor and two time US Scale Masters National Champion, my hope is to share whatever knowledge and practical advice I can for newcomers and seasoned competitors alike.
By Chris Wolfe 14 Feb, 2023
Are You Ready to Take Your RC Flying to the Next Level?? Then you’re in luck, because we’re giving away an FMS 1400mm F4U Corsair and an FMS 1100mm PC-21 ! But first, let's address the elephant in the room...it's been quite a while since my last blog post. With the move to TN and everything going on trying to get The RC Geek up and running full time, it's been difficult to sit down and set aside time to write. My goal is to change that going forward, so here's hoping! (check the vid below for even more details about everything mentioned here!)
By Chris Wolfe 25 Jan, 2022
Flight of the Flir Cat…The Sequel!! I tell you what, it has been quite the journey getting here! As a project, this Freewing F-14 Tomcat refinish took much longer than I had originally planned based on all of the other distractions that have come through the shop, but I'm so happy with how this model turned out in the end. It did take a few flights to get tuned and I have made a few small modifications in the process since our last installment, but otherwise I'm happy to report that the Tomcat is flying quite well. The F-14 Tomcat has such a great look and presence in the air, you just can't beat it!
By Chris 10 Jan, 2022
10 channels of power…and 1 receiver to rule them all! I personally love having the option for more channels, especially when building my own scale aircraft. While not always necessary, having channel options available is almost always helpful and it opens up opportunities to add scale functions and/or customize the controls more to your liking. And that's not to mention having individual servo setup across the same functions. So, I was excited to finally see the AR103060T and AR10100T 10 channel receivers released from Spektrum. It opens of channel options in a lighter weight package while also supports all of their new technology. Having been flying the NX10 for some time it is nice to finally be able to utilize all of those 10 radio channels.
By Chris 10 Jan, 2022
Good times and Warbird Flying are back! Needless to say, the last year and a half plus has been hard on all of us. With so many of our normal routines and activities disrupted, it has only brought that many more challenges it seems. This hobby is not just about the airplanes and flying, it is about the friends and comradery that can be enjoyed together with others as well. So, when the Scale Squadron's Warbirds & Classics came up again this year after being cancelled in 2020, I was beyond excited to go; it had been almost 2 years since the last event I went to!
By Chris 24 Nov, 2021
Refinish a Foam Jet Ep 4 – Freewing F-14 Tomcat Low-Viz Navy Weathering How low can you go?…a little low-viz Tomcat weathering. Finishing up the refinish work on the Freewing F-14 Tomcat, it’s time to apply some characteristic low-viz Navy weathering. The Flir Cat paint scheme is from the mid 90’s at a time when the Tomcats in service were painted primarily in Dark Ghost Grey (FS36320) with variations thereof. They were high maintenance workhorses at this time and the aircraft got extremely dirty during operation. This opens up lots of opportunities to apply different weathering techniques on the airplane to simulate those years of service on the carrier.
By Chris 24 Nov, 2021
Refinish a Foam Jet Ep 3 – Freewing F-14 Tomcat Paint, Markings, & Panel Lines
By Chris 27 Sep, 2021
Refinish A Foam Jet Ep 2 - Freewing F-14 Tomcat Cockpit 3D Printing, Painting and Moving Pilots
By Chris 27 Sep, 2021
Fill…sand…poly…sand…primer…sand…aaaannnnddd repeat… You've probably figured out by now, I have many favorite aircraft. ;) However, if I was to put together my top 5 favorite aircraft of all time, the F-14 Tomcat would probably be at or near the top of that list. The airplane was one of brute force, but packaged in an elegant and distinct looking airframe that truly personified its name, Tomcat. And that's not to mention, it was an extremely capable fighter that filled many roles through the years that operated from the early/mid 70's into the mid 2000s.
More Posts
Share by: